This is an old revision of the document!
MSPDEBUG
MSPDEBUG is used to program and debug MSP430 devices on Linux.
Pre-built
Install
apt-get install mspdebug
Test
rf2500
mspdebug rf2500
MSPDebug version 0.22 - debugging tool for MSP430 MCUs
Copyright (C) 2009-2013 Daniel Beer <dlbeer@gmail.com>
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
Trying to open interface 1 on 036
Initializing FET...
FET protocol version is 30394216
Set Vcc: 3000 mV
Configured for Spy-Bi-Wire
Device ID: 0x2553
Code start address: 0xc000
Code size : 16384 byte = 16 kb
RAM start address: 0x200
RAM end address: 0x3ff
RAM size : 512 byte = 0 kb
Device: MSP430G2553/G2403
Number of breakpoints: 2
fet: FET returned NAK
warning: device does not support power profiling
Chip ID data: 25 53
Available commands:
= erase isearch power save_raw simio
alias exit load prog set step
break fill load_raw read setbreak sym
cgraph gdb md regs setwatch verify
delbreak help mw reset setwatch_r verify_raw
dis hexout opt run setwatch_w
Available options:
color gdb_loop
enable_bsl_access gdbc_xfer_size
enable_locked_flash_access iradix
fet_block_size quiet
gdb_default_port
Type "help <topic>" for more information.
Use the "opt" command ("help opt") to set options.
Press Ctrl+D to quit.
(mspdebug)
Build
Install libmsp430.so
Fetch code and install libraries
cd /opt/src mkdir slac460y cd slac460y wget http://www.ti.com/lit/sw/slac460y/slac460y.zip unzip slac460y.zip apt-get install libboost-all-dev libhidapi-dev libusb-1.0-0-dev
Patch for Linux
wget https://dlbeer.co.nz/articles/slac460y/slac460y-linux.patch patch -p1 < slac460y-linux.patch
Fixes for modern boost
find -iname "*.cpp" -exec sed -i 's/(chrono/(std::chrono/g' {} \;
find -iname "*.cpp" -exec sed -i 's/boost::asio::io_service/boost::asio::io_context/g' {} \;
find -iname "*.h" -exec sed -i 's/boost::asio::io_service/boost::asio::io_context/g' {} \;
Build and install
make make install ldconfig
Install
cd /opt/src git clone https://github.com/dlbeer/mspdebug.git cd mspdebug apt-get install libusb-dev libreadline-dev make make install
Test
rf2500
mspdebug rf2500
MSPDebug version 0.25 - debugging tool for MSP430 MCUs
Copyright (C) 2009-2017 Daniel Beer <dlbeer@gmail.com>
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
Chip info database from MSP430.dll v3.15.0.1 Copyright (C) 2013 TI, Inc.
Trying to open interface 1 on 017
rf2500: warning: can't detach kernel driver: No data available
Initializing FET...
FET protocol version is 30394216
Set Vcc: 3000 mV
Configured for Spy-Bi-Wire
fet: FET returned error code 4 (Could not find device or device not supported)
fet: command C_IDENT1 failed
Using Olimex identification procedure
Device ID: 0x2553
Code start address: 0xc000
Code size : 16384 byte = 16 kb
RAM start address: 0x200
RAM end address: 0x3ff
RAM size : 512 byte = 0 kb
Device: MSP430G2xx3
Number of breakpoints: 2
fet: FET returned NAK
warning: device does not support power profiling
Chip ID data:
ver_id: 5325
ver_sub_id: 0000
revision: 00
fab: 60
self: 0000
config: 00
fuses: 00
Device: MSP430G2xx3
Available commands:
! fill power setwatch_r
= gdb prog setwatch_w
alias help read simio
blow_jtag_fuse hexout regs step
break isearch reset sym
cgraph load run verify
delbreak load_raw save_raw verify_raw
dis md set
erase mw setbreak
exit opt setwatch
Available options:
color gdb_loop
enable_bsl_access gdbc_xfer_size
enable_fuse_blow iradix
enable_locked_flash_access lowercase_dis
fet_block_size quiet
gdb_default_port
Type "help <topic>" for more information.
Use the "opt" command ("help opt") to set options.
Press Ctrl+D to quit.
(mspdebug)
ezfet
mspdebug ezfet
MSPDebug version 0.25 - debugging tool for MSP430 MCUs
Copyright (C) 2009-2017 Daniel Beer <dlbeer@gmail.com>
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
Chip info database from MSP430.dll v3.15.0.1 Copyright (C) 2013 TI, Inc.
Reset communications...
Version: 3.12.0.0 Core version: 0x1d, HIL version: 0x0d, HW: 0xaaacaaac
Reset firmware...
Set VCC: 3000 mV
Starting interface...
Device count: 1
Fetching JTAG ID...
ID: 99 00
Reset parameters...
hal_proto_execute: fid 0x07: HAL exception: 0xffc9
hal_proto_execute: fid: 0x07: failed
v3hil: can't set param 0x0d to 0x00000000
Check JTAG fuse...
Sync JTAG...
Identify (9x)...
Read device ID bytes at 0x01a00...
Read TLV...
ver_id: 82a1
ver_sub_id: 0000
revision: 21
fab: 55
self: 5555
config: 10
fuses: 55
activation_key: 00000000
Configuring for MSP430FR5994...
hal_proto_execute: fid 0x07: HAL exception: 0xffc9
hal_proto_execute: fid: 0x07: failed
v3hil: can't set param 0x0d to 0x00000000
Device: MSP430FR5994 [FRAM]
Available commands:
! fill power setwatch_r
= gdb prog setwatch_w
alias help read simio
blow_jtag_fuse hexout regs step
break isearch reset sym
cgraph load run verify
delbreak load_raw save_raw verify_raw
dis md set
erase mw setbreak
exit opt setwatch
Available options:
color gdb_loop
enable_bsl_access gdbc_xfer_size
enable_fuse_blow iradix
enable_locked_flash_access lowercase_dis
fet_block_size quiet
gdb_default_port
Type "help <topic>" for more information.
Use the "opt" command ("help opt") to set options.
Press Ctrl+D to quit.
(mspdebug)
