The I-NUCLEO-LRWAN1 is an SX1272 daughterboard with an STM32L052T8Y6 MCU.

This board comes as part of the P-NUCLEO-LRWAN2 kit and the motherboard is a NUCLEO-L073RZ.

Three I2C sensors exist on the board, a LSM303AGR, an HTS221 and a LPS22HB which are designed to be connected to the motherboard.

The I-NUCLEO-LRWAN1 is now obsolete but the embedded firmware can be replaced easily.

JP1 POWER
LSM303AGR 3V3

JP2 RESET
MCU RST

JP3 POWER
HTS221 3V3

JP4 POWER
LPS22HB 3V3

JP6 SWD
1 3V3
2 SWCLK
3 GND
4 SWDIO
5 RST

JP7 GROVE I2C
1 SCL
2 SDA
3 3V3
4 GND

JP8 DEBUG
1 SPI1 NSS
2 SPI1 MOSI
3 SPI1 MISO
4 SPI1 SCK

JP9 DEBUG
1 NRST RF
2 DIO0
3 DIO1
4 DIO2
5 DIO3
6 DIO4
7 DIO5

JP12 INTERRUPT
LSM303AGR INT

JP13 DEBUG
1 ANTENNA SWITCH 1
2 ANTENNA SWITCH 2

JP14 POWER MEASUREMENT
VDD RF

JP15 POWER MEASUREMENT
VDD 3V3

SWITCH
S1 RST

I2C
D15 SCL
D14 SDA

SYSTEM
D7 WAKEUP

LPS22H
D5 INT
D6 DRDY

LSM0303AGR
A5 INT
A6 DRDY

LED
A0 D1 GREEN

LPUART
D1 RX
D0 TX

PA9 RF RESET

PA12 SPI1 MOSI
PB4  SPI1 MISO
PB3  SPI1 SCK
PA15 SPI1 NSS

PA2  DIO0
PA3  DIO1
PA5  DIO2
PA6  DIO3
PA10 DIO4
PC7  DIO5 N/A

PA4 RF SWITCH CONTROL 1
PB8 RF SWITCH CONTROL 2

PB10 LPUART_TX
PB11 LPUART_RX

Switch the antenna of I-NUCLEO-LRWAN1 in TX mode
PA4 RF SWITCH CONTROL 1 = 1
PB8 RF SWITCH CONTROL 2 = 0

Switch the antenna of I-NUCLEO-LRWAN1 in RX mode
PA4 RF SWITCH CONTROL 1 = 0
PB8 RF SWITCH CONTROL 2 = 1

NO_CUSTOM_BAUD=1 picocom --imap lfcrlf --quiet -b 115200 /dev/ttyS5

+VER=1.0.1,2.9
+EUI=e2,4f,43,ff,fe,44,c3,84
+APPEUI=00,00,00,00,00,00,00,00
+AK=11,22,33,44,55,66,77,88,99,aa,bb,cc,dd,ee,ff,00

at+join=1,1
+JoinAccepted

Guide

It would appear that once the factory default firmware is wiped it cannot be restored, however, the default firmware appears to be buggy in any case.

Product page

Data brief

User manual

Firmware

P-NUCLEO-LRWAN1

P-NUCLEO-LRWAN2

USI WM-SG-SM-42 Product page

USI WM-SG-SM-42 Product spec

Arduino Shield Schematic

AT Command Reference Manual