These are cheap development boards with a STM32F030F4P6 Arm Cortex-M0 MCU which contains 16KB flash and 4KB ram.

These boards are quite wide and it's wise to attach the headers below only if two breadboards can be utilised side by side (see pictures).

These boards can be programmed using SWD or with the STM serial boot loader in ROM.

                 USB
         RESET   POWER
         SWITCH  LED
BOOT0                                5V
PF0          GND BOOT0 3V3           5V
PF1                                PA14
NRST                               PA13
VDDA                               PA10
PA0                                 PA9
PA1                                 PB1
PA2            8MHZ XTAL            PA7
PA3                                 PA6
PA4            LED                  PA5
GND                                 3V3
GND                                 3V3
   GND CLK DIO 3V3   RXD TXD GND 3V3

LED PA4
TXD PA9
RXD PA10
DIO PA13
CLK PA14

USART1 TX PA2 PA9
USART1 RX PA3 PA10

I2C1 SCL PA9
ICC1 SDA PA10

SPI1 NSS  PA4
SPI1 SCK  PA5
SPI1 MISO PA6
SPI1 MOSI PA7

Power is supplied on the USB socket which feeds a 3V3 LDO regulator. The USB socket does not support I/O, it's only for powering the device.

For testing this board use a UM232R for power, serial comms, reset and a source or external interrupt. Picocom is used to control the reset pin and provide a pulse for testing exti.

For programming, use J-Link device or OpenOCD.

   +--------+
   |        |TXD-----------RX
   |  FTDI  |DTR#----1K----PA0
USB| UM232R |RTS#---390R---NRST
   |        |RXD-----------TX
   |        |GND-----------GND
   |        |USB-----------5V
   +--------+
   +--------+
USB| JLINK/ |DIO-----------DIO
   | CLONE  |CLK-----------CLK
   +--------+   
   
USB on left is RPi host and USB on right is USB 5V pin on UM232R.

picocom -b 115200 /dev/ttyUSB0

CTRL A CTRL G will change the RTS line state from high to low. From the RS232 perspective it's inverted so when picocom says the line is low, it's actually a high output and the device is out of reset.

CTRL A CTRL P will pulse the DTR pin from low to high for 1 second.

Test SWD with J-Link and OpenOCD.

This uses the SEGGER J-Link EDU Mini. A command file is created containing the reset command and is issued to the processor.

Reset

/opt/JLink/JLinkExe -commandfile demov1.reset
SEGGER J-Link Commander V7.82a (Compiled Oct 31 2022 11:25:49)
DLL version V7.82a, compiled Oct 31 2022 11:25:22


J-Link Command File read successfully.
Processing script file...
J-Link>USB 801011752
Connecting to J-Link via USB...O.K.
Firmware: J-Link EDU Mini V1 compiled Oct 21 2022 11:17:52
Hardware version: V1.00
J-Link uptime (since boot): 0d 00h 53m 10s
S/N: 801011752
License(s): FlashBP, GDB
USB speed mode: Full speed (12 MBit/s)
VTref=3.299V
J-Link>Device STM32F030F4
J-Link>SelectInterface SWD
Selecting SWD as current target interface.
J-Link>Speed 4000
Selecting 4000 kHz as target interface speed
J-Link>Reset
Target connection not established yet but required for command.
Device "STM32F030F4" selected.


Connecting to target via SWD
InitTarget() start
InitTarget() end
Found SW-DP with ID 0x0BB11477
DPIDR: 0x0BB11477
CoreSight SoC-400 or earlier
Scanning AP map to find all available APs
AP[1]: Stopped AP scan as end of AP map has been reached
AP[0]: AHB-AP (IDR: 0x04770021)
Iterating through AP map to find AHB-AP to use
AP[0]: Core found
AP[0]: AHB-AP ROM base: 0xE00FF000
CPUID register: 0x410CC200. Implementer code: 0x41 (ARM)
Found Cortex-M0 r0p0, Little endian.
FPUnit: 4 code (BP) slots and 0 literal slots
CoreSight components:
ROMTbl[0] @ E00FF000
[0][0]: E000E000 CID B105E00D PID 000BB008 SCS
[0][1]: E0001000 CID B105E00D PID 000BB00A DWT
[0][2]: E0002000 CID B105E00D PID 000BB00B FPB
Cortex-M0 identified.
Reset delay: 0 ms
Reset type NORMAL: Resets core & peripherals via SYSRESETREQ & VECTRESET bit.
Reset: Halt core after reset via DEMCR.VC_CORERESET.
Reset: Reset device via AIRCR.SYSRESETREQ.
J-Link>Exit

Script processing completed.

OnDisconnectTarget() start
OnDisconnectTarget() end

demov1.reset

USB 801011752
Device STM32F030F4
SelectInterface SWD
Speed 4000
Reset
Exit

This uses a J-Link clone from China. This example programs and verifies the device before resetting to start execution.

Program

openocd -f "interface/jlink.cfg" -c "transport select swd" -f "target/stm32f0x.cfg" \
        -c "program demov1.bin preverify verify reset exit 0x8000000"
Open On-Chip Debugger 0.12.0-rc2+dev-00012-g4e077fdda (2022-11-12-16:05)
Licensed under GNU GPL v2
For bug reports, read
        http://openocd.org/doc/doxygen/bugs.html
swd
Info : J-Link ARM-OB STM32 compiled Aug 22 2012 19:52:04
Info : Hardware version: 7.00
Info : VTarget = 3.300 V
Info : clock speed 1000 kHz
Info : SWD DPIDR 0x0bb11477
Info : [stm32f0x.cpu] Cortex-M0 r0p0 processor detected
Info : [stm32f0x.cpu] target has 4 breakpoints, 2 watchpoints
Info : starting gdb server for stm32f0x.cpu on 3333
Info : Listening on port 3333 for gdb connections
[stm32f0x.cpu] halted due to debug-request, current mode: Thread
xPSR: 0xc1000000 pc: 0x08000664 msp: 0x20001000
**pre-verifying**
**Verified OK - No flashing**
** Resetting Target **
shutdown command invoked

Product page

MCU datasheet

MCU reference manual