You are here: start » tools » openocd

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
tools:openocd [2024/10/17 17:54] – [Install] darrontools:openocd [2025/02/23 18:10] (current) – darron
Line 13: Line 13:
 ===Install=== ===Install===
  
-==RPi==+Build from source enabling every supported interface type. 
 + 
 +==Dependencies==
  
 Install prerequisites. Install prerequisites.
  
 <code> <code>
-apt install build-essential git automake libtool libhidapi-dev libcapstone-dev libusb-1.0-0-dev libjaylink-dev libgpiod-dev +apt install build-essential git automake libtool libhidapi-dev libcapstone-dev libusb-1.0-0-dev libjaylink-dev libgpiod-dev libftdi-dev pkg-config
-pkg-config+
 </code> </code>
 +
 +==Dev==
  
 Install into /usr/local Install into /usr/local
Line 27: Line 30:
 mkdir -p /opt/src mkdir -p /opt/src
 cd /opt/src cd /opt/src
-git clone https://git.code.sf.net/p/openocd/code openocd+git clone --recursive https://git.code.sf.net/p/openocd/code openocd
 cd openocd cd openocd
 ./bootstrap ./bootstrap
-./configure --prefix=/usr/local --enable-ftdi --enable-sysfsgpio --enable-bcm2835gpio --enable-picoprobe --enable-jlink --enable-ft232r --enable-cmsis-dap --enable-cmsis-dap-v2 --with-capstone+./configure --prefix=/usr/local --enable-ftdi --enable-sysfsgpio --enable-bcm2835gpio --enable-picoprobe --enable-jlink --enable-ft232r --enable-cmsis-dap --enable-cmsis-dap-v2 --enable-dummy --with-capstone --enable-openjtag --enable-aice --enable-presto --enable-usb-blaster --enable-internal-jimtcl
 make -j 4 make -j 4
 make install make install
 </code> </code>
  
-ST and RPi provide modified versions of OpenOCD for their processors+STMicroelectronics and RPi provide modified versions of OpenOCD for their processors 
 + 
 +==STM== 
 + 
 +Install into /opt
  
 <code> <code>
 +mkdir -p /opt/src
 +cd /opt/src
 git clone https://github.com/STMicroelectronics/OpenOCD openocd.stm git clone https://github.com/STMicroelectronics/OpenOCD openocd.stm
-... +cd openocd.stm 
-./configure --prefix=/opt/openocd.stm ...+./bootstrap 
 +./configure --prefix=/opt/openocd.stm --enable-ftdi --enable-sysfsgpio --enable-bcm2835gpio --enable-picoprobe --enable-jlink --enable-ft232r --enable-cmsis-dap --enable-cmsis-dap-v2 --enable-dummy --with-capstone --enable-openjtag --enable-aice --enable-presto --enable-usb-blaster 
 +make -j 4 
 +make install
 </code> </code>
 +
 +==RPi==
 +
 +Install into /opt
  
 <code> <code>
 +mkdir -p /opt/src
 +cd /opt/src
 git clone https://github.com/raspberrypi/openocd openocd.rpi git clone https://github.com/raspberrypi/openocd openocd.rpi
 +cd openocd.rpi
 +./bootstrap
 +./configure --prefix=/opt/openocd.rpi --enable-ftdi --enable-sysfsgpio --enable-bcm2835gpio --enable-picoprobe --enable-jlink --enable-ft232r --enable-cmsis-dap --enable-cmsis-dap-v2 --enable-dummy --with-capstone --enable-openjtag --enable-aice --enable-presto --enable-usb-blaster
 +make -j 4
 +make install
 +</code>
 +
 +==Test==
 +
 +<code>
 +/opt/openocd.rpi/bin/openocd -f "interface/cmsis-dap.cfg" -f "target/rp2350.cfg" -c "adapter speed 4000"
 +Open On-Chip Debugger 0.12.0+dev-gebec9504d (2024-10-17-18:47)
 +Licensed under GNU GPL v2
 +For bug reports, read
 +        http://openocd.org/doc/doxygen/bugs.html
 +Info : Hardware thread awareness created
 +Info : Hardware thread awareness created
 +Info : Hardware thread awareness created
 +Info : Hardware thread awareness created
 +cortex_m reset_config sysresetreq
 +adapter speed: 4000 kHz
 +Info : Listening on port 6666 for tcl connections
 +Info : Listening on port 4444 for telnet connections
 +Info : Using CMSIS-DAPv2 interface with VID:PID=0x2e8a:0x000c, serial=1C789DE3E289C250
 +Info : CMSIS-DAP: SWD supported
 +Info : CMSIS-DAP: Atomic commands supported
 +Info : CMSIS-DAP: Test domain timer supported
 +Info : CMSIS-DAP: FW Version = 2.0.0
 +Info : CMSIS-DAP: Interface Initialised (SWD)
 +Info : SWCLK/TCK = 0 SWDIO/TMS = 0 TDI = 0 TDO = 0 nTRST = 0 nRESET = 0
 +Info : CMSIS-DAP: Interface ready
 +Info : clock speed 4000 kHz
 +Info : SWD DPIDR 0x4c013477
 +Info : [rp2350.dap.core0] Cortex-M33 r1p0 processor detected
 +Info : [rp2350.dap.core0] target has 8 breakpoints, 4 watchpoints
 +Info : [rp2350.dap.core0] Examination succeed
 +Info : [rp2350.dap.core1] Cortex-M33 r1p0 processor detected
 +Info : [rp2350.dap.core1] target has 8 breakpoints, 4 watchpoints
 +Info : [rp2350.dap.core1] Examination succeed
 +Info : starting gdb server for rp2350.dap.core0 on 3333
 +Info : Listening on port 3333 for gdb connections
 +</code>
 +
 +==Update==
 +
 +<code>
 +make distclean
 +git pull --recurse-submodules
 ... ...
-./configure --prefix=/opt/openocd.rpi ... 
 </code> </code>