Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| tools:meshtastic [2024/08/28 12:47] – [Resources] darron | tools:meshtastic [2024/09/11 11:25] (current) – [Command Line Interface] darron | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====Meshtastic==== | ====Meshtastic==== | ||
| - | ===CLI=== | + | ===Mestastic Linux=== |
| + | |||
| + | Using the [[interfaces: | ||
| + | |||
| + | ==Raspberry Pi Zero 2W / Pi 3B== | ||
| + | |||
| + | __Kernel configuration__ | ||
| < | < | ||
| - | apt install python3-full | + | dtparam=spi=on |
| + | dtoverlay=spi0-0cs | ||
| + | enable_uart=1 | ||
| </ | </ | ||
| + | |||
| + | __Kernel command line__ | ||
| + | |||
| + | < | ||
| + | console=tty1 root=PARTUUID=xxxxxxxx-02 rootfstype=ext4 fsck.repair=yes rootwait cfg80211.ieee80211_regdom=GB | ||
| + | </ | ||
| + | |||
| + | __Meshtastic__ | ||
| + | |||
| + | < | ||
| + | Lora: | ||
| + | Module: sx1262 | ||
| + | DIO2_AS_RF_SWITCH: | ||
| + | CS: 21 | ||
| + | IRQ: 16 | ||
| + | Busy: 20 | ||
| + | Reset: 18 | ||
| + | | ||
| + | GPS: | ||
| + | SerialPath: /dev/ttyS0 | ||
| + | | ||
| + | Logging: | ||
| + | LogLevel: debug # debug, info, warn, error | ||
| + | |||
| + | Webserver: | ||
| + | Port: 443 # Port for Webserver & Webservices | ||
| + | RootPath: / | ||
| + | </ | ||
| + | |||
| + | __Runit__ | ||
| + | |||
| + | < | ||
| + | systemctl stop meshtasticd | ||
| + | systemctl disable meshtasticd | ||
| + | systemctl mask meshtasticd | ||
| + | </ | ||
| + | |||
| + | < | ||
| + | #! /bin/bash | ||
| + | sleep 1 | ||
| + | |||
| + | #LOG | ||
| + | exec 2>&1 | ||
| + | ulimit -aH | ||
| + | |||
| + | #RUN | ||
| + | mkdir -p / | ||
| + | cd / | ||
| + | exec / | ||
| + | </ | ||
| + | |||
| + | |||
| + | ===Command Line Interface=== | ||
| + | |||
| + | ==Setup== | ||
| + | |||
| + | < | ||
| + | sudo apt install python3-full | ||
| + | </ | ||
| + | |||
| + | == Install== | ||
| < | < | ||
| Line 25: | Line 94: | ||
| < | < | ||
| meshtastic --port / | meshtastic --port / | ||
| + | </ | ||
| + | |||
| + | ==Update== | ||
| + | |||
| + | < | ||
| + | ~/ | ||
| + | </ | ||
| + | ===Channel=== | ||
| + | |||
| + | < | ||
| + | meshtastic --port / | ||
| + | Connected to radio | ||
| + | Set name to HOME | ||
| + | Writing modified channels to device | ||
| + | |||
| + | meshtastic --port / | ||
| + | Connected to radio | ||
| + | Writing modified channels to device | ||
| </ | </ | ||
| Line 32: | Line 119: | ||
| ==Receive== | ==Receive== | ||
| - | |||
| __Install__ | __Install__ | ||
| Line 74: | Line 160: | ||
| ==Send== | ==Send== | ||
| + | |||
| + | Direct message | ||
| < | < | ||
| meshtastic --port / | meshtastic --port / | ||
| </ | </ | ||
| + | |||
| + | Channel message | ||
| + | |||
| + | < | ||
| + | meshtastic --port / | ||
| + | </ | ||
| + | |||
| ===Info=== | ===Info=== | ||
| + | |||
| + | These are some parameters which can be used to sniff | ||
| + | the LoRa radio with [[: | ||
| < | < | ||
| Line 101: | Line 199: | ||
| [[https:// | [[https:// | ||
| + | |||
| + | [[https:// | ||
| [[https:// | [[https:// | ||
