You are here: start » tools » bluetooth

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
tools:bluetooth [2023/12/06 06:02] – [Development] darrontools:bluetooth [2023/12/15 07:48] (current) – [Python] darron
Line 1: Line 1:
 ====Bluetooth==== ====Bluetooth====
- 
-There are two standards in use known as BT classic and BT low energy. 
- 
-Anything other than BLE is considered obsolete now. 
- 
-^HCI / LMP^Version^ 
-|0| 1.0b| 
-|1| 1.1| 
-|2| 1.2| 
-|3| 2.0+EDR| 
-|4| 2.1+EDR| 
-|5| 3.0+HS| 
-|6| 4.0| 
-|7| 4.1| 
-|8| 4.2| 
-|9| 5.0| 
-|10| 5.1| 
-|11| 5.2| 
-|12| 5.3| 
- 
-BT 3.0+HS utilises WiFi. BT 4.0 onward is BLE, anything prior is BDR/EDR. 
  
 See [[interfaces:bluetooth]] for Linux Bluetooth devices and setup. See [[interfaces:bluetooth]] for Linux Bluetooth devices and setup.
Line 26: Line 5:
 ===Services=== ===Services===
  
-Development has two services dependencies, dbus and bluetoothd.+Development has two service dependencies, dbus and bluetoothd.
  
 ==DBUS== ==DBUS==
Line 75: Line 54:
  
 ===C development=== ===C development===
 +
 +Development in C is mostly about reading the code examples.
  
 ==Headers== ==Headers==
Line 103: Line 84:
 </code> </code>
  
-=== Test===+== Test==
  
-Test [[:boards:wb15|BLE]] device.+Test [[:boards:wb15|STM32WB15CC]] BLE device.
  
 <code> <code>
Line 134: Line 115:
 </code> </code>
  
 +LED on/off for demo connection above.
 +
 +<code>
 +[GATT client]# write-value -w 0x000E 0x01 0x01
 +Write command sent
 +[GATT client]# write-value -w 0x000E 0x01 0x00
 +Write command sent
 +[GATT client]#
 +</code>
  
 ===Python=== ===Python===
 +
 +It's certainly a lot easier to write code to access BLE devices
 +in Python and preferred for demo purposes and maybe even
 +end use cases.
  
 <code> <code>
 apt install python3-gattlib apt install python3-gattlib
 </code> </code>
 +
 +Example for the [[:boards:wb15|STM32WB15CC]] BLE demo.
 +
 +<code>
 +import sys, time
 +
 +from gattlib import GATTRequester
 +
 +req = GATTRequester("00:80:E1:22:F9:7C", False)
 +
 +req.connect(True)
 +
 +for n in range(10):
 +    req.write_cmd(0x000E, bytes([0x01,0x01]))
 +    time.sleep(1)
 +    req.write_cmd(0x000E, bytes([0x01,0x00]))
 +    time.sleep(1)
 +
 +req.disconnect()
 +</code> 
 +