This is an old revision of the document!
Table of Contents
Xino basic for PIC
The XINO Basic for PIC/PICAXE is compatible with any 18-pin device which has a
UART with RX on pin 8 and TX on pin 11 (Eg. 16F88 but not 16F627) and has an
internal oscillator. The on-board XTAL is not connected to the 18-pin socket.
All 28-pin devices should be compatible which have a UART on pins 17 and 18.
(This product has been discontinued).
PIC16F88 (REPLACING PICAXE 18M2 = PIC16F1847)
RA2 AN2 VREF- CVREF 1----18 RA1 AN1 RA3 AN3 VREF+ C1OUT 2 17 RA0 AN0 RA4 AN4 T0CKI C2OUT 3 16 RA7 OSC1 CLKI RA5 !MCLR VPP 4 15 RA6 OSC2 CLKO VSS/GND 5 14 VDD/VCC RB0 INT CCP1 6 13 RB7 AN6 PGD T1OSI RB1 SDI SDA 7 12 RB6 AN5 PGC T1OSO T1CKI RB2 SDO RX DT 8 11 RB5 !SS TX CK RB3 PGM CCP1 9----10 RB4 SCK SCL
I/O
HEADER
------
P0 NC 15 NC
P1 NC 14 5 VSS GND
RST NC 13 10 RB4 SCK SCL
3V3 14 VDD/VCC JUMPER=3V3 12 7 RB1 SDI SDA
5V 14 VDD/VCC JUMPER=5V 11 15 RA6 OSC2 CLKO
GND 5 VSS/GND 10 2 RA3 AN3 VREF+ C1OUT
GND 5 VSS/GND 09 NC
VIN NC 08 16 RA7 OSC1 CLKI
A0 1 RA2 AN2 VREF- CVREF 07 NC
A1 13 RB7 AN6 PGD T1OSI 06 NC
A2 17 RA0 AN0 05 NC
A3 18 RA1 AN1 04 9 RB3 PGM CCP1
A4 3 RA4 AN4 T0CKI C2OUT 03 12 RB6 AN5 PGC T1OSO T1CKI
A5 4 RA5 !MCLR VPP 02 6 RB0 INT CCP1
01 11 RB5 !SS TX CK
SERIAL 00 8 RB2 SDO RX DT
------
RST NC JACK
GND 5 VSS/GND ----
MCUPWR 14 VDD/VCC SLEEVE 2 RA3
TX 11 RB5 !SS TX CK RING 3 RA4
RX 8 RB2 SDO RX DT TIP GROUND
ICSP
----
1:VPP 12V A5 TIE WITH 9V1 ZENER FOR 9V HVP
2:VDD 5V 5V
3:VSS/GND GND
4:PGD A1
5:PGC 03
PGM 04 TIE WITH 100K TO GND FOR HVP
PIC18F2320 (REPLACING PICAXE 28X2 = PIC18F25K22)
!MCLR VPP 1----28 RB7 KBI3 PGD RA0 AN0 2 27 RB6 KBI2 PGC RA1 AN1 3 26 RB5 KBI1 PGM RA2 AN2 VREF- CVREF 4 25 RB4 KBI0 AN11 RA3 AN3 VREF+ 5 24 RB3 AN9 CCP2 RA4 T0CKI C1OUT 6 23 RB2 AN8 INT2 RA5 AN4 !SS LVDIN C2OUT 7 22 RB1 AN10 INT1 VSS GND 8 21 RB0 AN12 INT0 OSC1 CLKI RA7 9 20 VDD VCC OSC2 CLKO RA6 10 19 VSS GND RC0 T1OSO T1CKI 11 18 RC7 RX DT RC1 T1OSI CCP2 12 17 RC6 TX CK RC2 CCP1 P1A 13 16 RC5 SDO RC3 SCK SCL 14---15 RC4 SDI SDA
I/O
HEADER
------
P0 12 RC1 T1OSI CCP2 15 NC
P1 13 RC2 CCP1 P1A 14 8/19 VSS GND
RST 1 !MCLR VPP 13 14 RC3 SCK SCL
3V3 20 VDD/VCC JUMPER=3V3 12 15 RC4 SDI SDA
5V 20 VDD/VCC JUMPER=5V 11 16 RC5 SDO
GND 8/19 VSS/GND 10 7 RA5 AN4 !SS LVDIN C2OUT
GND 8/19 VSS/GND 09 28 RB7 KBI3 PGD
VIN NC 08 27 RB6 KBI2 PGC
A0 2 RA0 AN0 07 26 RB5 KBI1 PGM
A1 3 RA1 AN1 06 25 RB4 KBI0 AN11
A2 4 RA2 AN2 VREF- CVREF 05 24 RB3 AN9 CCP2
A3 5 RA3 AN3 VREF+ 04 23 RB2 AN8 INT2
A4 6 RA4 T0CKI C1OUT 03 22 RB1 AN10 INT1
A5 11 RC0 T1OSO T1CKI 02 21 RB0 AN12 INT0
01 17 RC6 TX CK
SERIAL 00 18 RC7 RX DT
------
RST 1 !MCLR VPP JACK XTAL
GND 8 VSS/GND ---- ----
MCUPWR 20 VDD/VCC SLEEVE 7 RA5 9 OSC1 CLKI RA7
TX 17 RC6 TX CK RING 6 RA4 10 OSC2 CLKO RA6
RX 18 RC7 RX DT TIP GROUND
ICSP
----
1:VPP 12V RST TIE WITH 9V1 ZENER FOR 9V HVP
2:VDD 5V 5V
3:VSS/GND GND
4:PGD 09
5:PGC 08
PGM 07 TIE WITH 100K TO GND FOR HVP
