smartctl 6.6 2017-11-05 r4594 [armv7l-linux-4.19.66-v7l+] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax Plus 9
Device Model: Maxtor 6Y080M0
Serial Number: Y22025DC
Firmware Version: YAR51HW0
User Capacity: 81,964,302,336 bytes [81.9 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 T13/1532D revision 0
Local Time is: Mon Oct 14 09:44:00 2019 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 30) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 37) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 226 225 063 Pre-fail Always - 9742
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 1235
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 252 239 187 Pre-fail Always - 57007
9 Power_On_Minutes 0x0032 230 230 000 Old_age Always - 428h+06m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 250 250 000 Old_age Always - 1225
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 45
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 1425
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 2
202 Data_Address_Mark_Errs 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 1
204 Soft_ECC_Correction 0x000a 253 252 000 Old_age Always - 0
205 Thermal_Asperity_Rate 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 253 253 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 267 inconsistent with error log pointer 5
ATA Error Count: 267 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 267 occurred at disk power-on lifetime: 7567 hours (315 days + 7 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 06 27 4a 0f e0 Error: UNC 6 sectors at LBA = 0x000f4a27 = 1002023
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 08 27 4a 0f e0 00 01:30:27.536 READ DMA EXT
25 03 08 3f 66 60 e0 00 01:30:27.520 READ DMA EXT
25 03 08 0f 18 17 e0 00 01:30:27.504 READ DMA EXT
25 03 40 47 78 19 e0 00 01:30:27.360 READ DMA EXT
25 03 40 5f a0 5f e0 00 01:30:27.344 READ DMA EXT
Error 266 occurred at disk power-on lifetime: 7566 hours (315 days + 6 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 37 70 49 0f e0 Error: UNC 55 sectors at LBA = 0x000f4970 = 1001840
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 f0 70 49 0f e0 00 00:06:25.504 READ DMA EXT
25 03 10 60 49 0f e0 00 00:06:25.504 READ DMA EXT
25 03 f0 70 48 0f e0 00 00:06:25.504 READ DMA EXT
25 03 10 60 48 0f e0 00 00:06:25.504 READ DMA EXT
25 03 f0 70 47 0f e0 00 00:06:25.504 READ DMA EXT
Error 265 occurred at disk power-on lifetime: 7566 hours (315 days + 6 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 06 27 4a 0f e0 Error: UNC 6 sectors at LBA = 0x000f4a27 = 1002023
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 d5 08 27 4a 0f e0 00 00:05:15.600 READ DMA EXT
25 d5 40 4f 7b 18 e0 00 00:05:15.584 READ DMA EXT
25 d5 08 cf f9 62 e0 00 00:05:15.584 READ DMA EXT
25 d5 08 27 22 a9 e0 00 00:05:15.584 READ DMA EXT
25 d5 08 d7 f9 62 e0 00 00:05:15.568 READ DMA EXT
Error 264 occurred at disk power-on lifetime: 7566 hours (315 days + 6 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 06 27 4a 0f e0 Error: UNC 6 sectors at LBA = 0x000f4a27 = 1002023
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 08 27 4a 0f e0 00 00:07:06.112 READ DMA EXT
25 03 60 77 00 60 e0 00 00:07:06.096 READ DMA EXT
25 03 08 57 1c 62 e0 00 00:07:06.080 READ DMA EXT
25 03 50 d7 1a 60 e0 00 00:07:06.080 READ DMA EXT
25 03 08 c7 1a 60 e0 00 00:07:06.080 READ DMA EXT
Error 263 occurred at disk power-on lifetime: 7566 hours (315 days + 6 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 77 20 4a 0f e0 Error: UNC 119 sectors at LBA = 0x000f4a20 = 1002016
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 80 20 4a 0f e0 00 00:06:17.216 READ DMA EXT
25 03 80 a0 49 0f e0 00 00:06:17.216 READ DMA EXT
25 03 80 20 49 0f e0 00 00:06:17.200 READ DMA EXT
25 03 40 e0 48 0f e0 00 00:06:17.184 READ DMA EXT
25 03 40 a0 48 0f e0 00 00:06:17.168 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 7568 -
# 2 Short offline Completed: read failure 60% 7566 1002025
# 3 Short offline Completed: read failure 60% 7565 1002025
# 4 Short offline Completed: read failure 60% 7565 1002025
# 5 Short offline Completed: read failure 60% 7564 1002025
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
