Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| boards:wio-e5 [2024/08/30 18:31] – [Pinout] darron | boards:wio-e5 [2024/09/25 13:51] (current) – [Resources] darron | ||
|---|---|---|---|
| Line 9: | Line 9: | ||
| </ | </ | ||
| - | This board has a package containing a STM32WLE5JC | + | This board has a package containing a STM32WLE5JC |
| - | The MCU does not contain a FPU, only the mandatory DSP for m4 | + | The MCU does not contain a FPU, only the mandatory DSP for M4 |
| cores, but it does have an embedded radio, it appears to be an SX1262. | cores, but it does have an embedded radio, it appears to be an SX1262. | ||
| Line 32: | Line 32: | ||
| the device may be destroyed." | the device may be destroyed." | ||
| - | I probably would not have bothered with this board had I read the above warning beforehand. | ||
| - | Who designs a MCU that can self destruct if a bit doesn' | ||
| Line 69: | Line 67: | ||
| </ | </ | ||
| - | Once testing is complete | + | Once testing is complete erase the firmware |
| - | so there is no going back since it' | + | |
| Line 198: | Line 195: | ||
| </ | </ | ||
| - | ===Pinout=== | + | ===Pin control=== |
| < | < | ||
| Line 207: | Line 203: | ||
| </ | </ | ||
| + | ===RF switch=== | ||
| + | |||
| + | < | ||
| + | OFF | ||
| + | PA4 RF_SW_CTRL1 = 0 | ||
| + | PA5 RF_SW_CTRL2 = 0 | ||
| + | |||
| + | RX | ||
| + | PA4 RF_SW_CTRL1 = 1 | ||
| + | PA5 RF_SW_CTRL2 = 0 | ||
| + | |||
| + | RFO_LP | ||
| + | PA4 RF_SW_CTRL1 = 1 | ||
| + | PA5 RF_SW_CTRL2 = 1 | ||
| + | |||
| + | RFO_HP | ||
| + | PA4 RF_SW_CTRL1 = 0 | ||
| + | PA5 RF_SW_CTRL2 = 1 | ||
| + | </ | ||
| + | |||
| + | According to the product WIKI RFO_LP is not supported. | ||
| ===Clock=== | ===Clock=== | ||
| Line 214: | Line 231: | ||
| 32MHz TCXO | 32MHz TCXO | ||
| - | |||
| - | < | ||
| - | PB0 TCXO VCC | ||
| - | </ | ||
| ==LSE== | ==LSE== | ||
| 32.768KHz | 32.768KHz | ||
| - | ===Antenna=== | ||
| - | ==Receiver== | + | ===LoRaWAN firmware=== |
| - | < | + | The I-CUBE LoRaWAN demo has been updated to support GNU make [[https:// |
| - | PA4 1 | + | |
| - | PA5 0 | + | |
| - | </code> | + | |
| - | ==Transmitter with RFO_HP== | ||
| - | |||
| - | < | ||
| - | PA4 0 | ||
| - | PA5 1 | ||
| - | </ | ||
| - | |||
| - | SMPS mode. | ||
| - | |||
| - | ==Transmitter with RFO_LP== | ||
| - | |||
| - | Not supported. | ||
| ===Resources=== | ===Resources=== | ||
| Line 255: | Line 252: | ||
| [[https:// | [[https:// | ||
| - | [[https:// | + | [[https:// |
| + | |||
| + | [[https:// | ||
| [[https:// | [[https:// | ||
| [[https:// | [[https:// | ||
| - | |||
| {{[downloads: | {{[downloads: | ||
