Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| projects:wellington [2017/01/28 06:29] – [Upload] darron | projects:wellington [2017/03/11 02:00] (current) – [Devices] darron | ||
|---|---|---|---|
| Line 12: | Line 12: | ||
| For the UART interface any of a number of serial interfaces may | For the UART interface any of a number of serial interfaces may | ||
| be used which includes bluetooth devices such as the [[interfaces: | be used which includes bluetooth devices such as the [[interfaces: | ||
| + | === Devices === | ||
| + | |||
| + | At this time 192 devices are thought to be supported and here is a list | ||
| + | of devices which have been tested during the production of this boot loader. | ||
| + | |||
| + | <columns 50% 50% -> | ||
| + | |||
| + | < | ||
| + | pic18f13k50 | ||
| + | pic18f25k22 | ||
| + | pic18f25k50 | ||
| + | pic18f26j50 | ||
| + | pic18f26k20 | ||
| + | pic18f26k40 | ||
| + | </ | ||
| + | |||
| + | < | ||
| + | |||
| + | < | ||
| + | pic18f26k80 | ||
| + | pic18f4520 | ||
| + | pic18f4550 | ||
| + | pic18f4620 | ||
| + | pic18f4685 | ||
| + | </ | ||
| + | |||
| + | </ | ||
| + | |||
| + | The pic18f26k80 and pic18f4685 support both serial and CAN Bus. | ||
| === Licence === | === Licence === | ||
| Line 21: | Line 50: | ||
| Wellington Boot Loader is developed by Darron M Broad with contributions from Gerhard Bertelsmann. | Wellington Boot Loader is developed by Darron M Broad with contributions from Gerhard Bertelsmann. | ||
| - | I am grateful to Chiculita Claudiu for his Tiny PIC Bootloader as Wellington Boot Loader uses methods | + | I am grateful to Chiculita Claudiu for Tiny PIC Bootloader as Wellington Boot Loader uses a protocol |
| - | I must also thank Mikael Gustavsson for his efforts with ds30 Loader. The device files are derived from ds30 Loader. | ||
| - | === Install | + | === Checkout |
| - | The following operations will install the loader | + | Wellington boot loader |
| < | < | ||
| hg clone http:// | hg clone http:// | ||
| cd wellington | cd wellington | ||
| - | make | ||
| - | sudo make install | ||
| </ | </ | ||
| Line 48: | Line 74: | ||
| Follow the guide given in the template to create the correct boot loader | Follow the guide given in the template to create the correct boot loader | ||
| - | firmware for your target then build the boot loader. | + | firmware for your target then build the boot loader. [[: |
| < | < | ||
| Line 73: | Line 99: | ||
| and upload it to the boot loader which will store it in flash memory. | and upload it to the boot loader which will store it in flash memory. | ||
| - | First install easy-loader. | + | This process is documented on the [[:projects: |
| - | < | + | |
| - | hg clone http:// | + | |
| - | cd easy-loader | + | |
| - | make | + | |
| - | sudo make install | + | |
| - | </ | + | |
| - | + | ||
| - | Now upload application to target. | + | |
| - | < | + | |
| - | easy-loader /dev/ttyX myapp.hex | + | |
| - | </ | + | |
| - | + | ||
| - | After uploading, easy-loader will instruct the Boot Loader to | + | |
| - | run the application. | + | |
