Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| projects:esp [2015/02/04 18:14] – [PCF8591] darron | projects:esp [2017/01/12 22:44] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 10: | Line 10: | ||
| The three devices are a Microchip MCP23016 digital I/O expander, NXP PCF8591 ADC/DAC and Microchip 24LC512 EEPROM. | The three devices are a Microchip MCP23016 digital I/O expander, NXP PCF8591 ADC/DAC and Microchip 24LC512 EEPROM. | ||
| - | These were chosen because they add useful capabilities to the ESP-01 or RPi and all three are available in DIP format from CPC in the United Kingdom. | + | These were chosen because they add useful |
| + | You may also consider adding an I2C RTC to this project and perhaps it shall be updated to include one at a later time. | ||
| === Schematic === | === Schematic === | ||
| + | |||
| + | The circuit is expected to be used with either an ESP-01 attached and with its UART connected to a computer to load in scripts, else without an ESP-01 and with the I2C lines connected to a Raspberry Pi. | ||
| {{: | {{: | ||
| + | It should be reasonably simple to construct on stripboard. Tripad board will be used to demonstrate this at a later time. | ||
| === I2C bus === | === I2C bus === | ||
| + | |||
| + | The I2C bus is simple affair with only two lines required for its operation. This is perfect for the ESP-01 module which only has two GPIOs exposed on its header pins. For the Raspberry Pi, there are two I2C buses, but only one is normally available. | ||
| ^Address ^Device | | ^Address ^Device | | ||
| Line 22: | Line 28: | ||
| |0x48 |PCF8591| | |0x48 |PCF8591| | ||
| |0x50 |24LC512| | |0x50 |24LC512| | ||
| + | |||
| + | These addresses are the defaults for all three devices with the address pins tied low. Multiple devices of the same type are easily accommodated on the I2C bus but this is not demonstrated here. | ||
| Probing the bus on the RPi with [[: | Probing the bus on the RPi with [[: | ||
| Line 37: | Line 45: | ||
| </ | </ | ||
| === MCP23016 === | === MCP23016 === | ||
| + | |||
| + | The MCP23016 is general purpose digital I/O expander. There are more modern and faster varieties of this device but as yet they are not available at CPC. | ||
| ^Control ^Register ^Function | | ^Control ^Register ^Function | | ||
| Line 50: | Line 60: | ||
| == ESP-01 NodeMcu == | == ESP-01 NodeMcu == | ||
| - | First we need eSPY, fetch and build it. The examples | + | The NodeMcu firmware can be controlled via a serial console. This can be a manual operation else with a specially written tool for the job: eSPY. |
| + | |||
| + | First we need to fetch eSPY, and then build it. The examples | ||
| < | < | ||
| hg clone http:// | hg clone http:// | ||
| Line 94: | Line 106: | ||
| </ | </ | ||
| - | The script comes with the eSPY application and can be demomstrated | + | The script comes with the eSPY application and can be demomstrated |
| < | < | ||
| ./mcp.esp | ./mcp.esp | ||
| Line 128: | Line 140: | ||
| === PCF8591 === | === PCF8591 === | ||
| + | |||
| + | The PCF8591 combines 4 analogue inputs and a single analogue output. The inputs can be more than simple input channels but this isn't looked at here. | ||
| + | |||
| ^Control ^Register | ^Control ^Register | ||
| |0 | channel 0 |Read ADC 0| | |0 | channel 0 |Read ADC 0| | ||
| Line 173: | Line 188: | ||
| </ | </ | ||
| - | When the script is run with eSPY we can see the DAC output ramp up and a running | + | When the script is run with eSPY we can see the DAC output ramp up with a running |
| < | < | ||
| 0 | 0 | ||
| Line 208: | Line 223: | ||
| I2C EEPROMs have varied addressing schemes. The simplest is a 8-bit address offset, another one where a block selection is made with an I2C address and a byte selection is made with an 8-bit address offset. Yet another, where the I2C address is fixed but it now has a 16-bit address offset and lastly one with both of the last methods combined. | I2C EEPROMs have varied addressing schemes. The simplest is a 8-bit address offset, another one where a block selection is made with an I2C address and a byte selection is made with an 8-bit address offset. Yet another, where the I2C address is fixed but it now has a 16-bit address offset and lastly one with both of the last methods combined. | ||
| - | Here we will demonstrate the 24LC512 | + | The 24LC512 |
| - | On the RPi we can reset the internal address pointer of the chip to 0 like this. | + | == ESP-01 NodeMcu == |
| - | < | + | |
| - | i2cset | + | |
| - | </ | + | |
| - | + | ||
| - | To read, we first write an address to start at then begin reading, if we keep reading the address is auto-incremented. | + | |
| - | < | + | |
| - | i2cset -y 1 0x50 0 0 | + | |
| - | i2cget -y 1 0x50 | + | |
| - | 0x55 | + | |
| - | i2cget -y 1 0x50 | + | |
| - | 0xaa | + | |
| - | </ | + | |
| - | + | ||
| - | If we want to write to a location we send the address followed by the byte of data. | + | |
| - | < | + | |
| - | i2cset -y 1 0x50 0 0 0xEE i | + | |
| - | i2cset -y 1 0x50 0 0 | + | |
| - | i2cget -y 1 0x50 | + | |
| - | 0xee | + | |
| - | </ | + | |
| On the ESP-01 we can use this NodeMcu LUA script to read the EEPROM. | On the ESP-01 we can use this NodeMcu LUA script to read the EEPROM. | ||
| Line 267: | Line 262: | ||
| </ | </ | ||
| - | Here the script is executed using eSPY (to be documented). | + | Here the script is executed using eSPY. |
| < | < | ||
| ./ | ./ | ||
| - | > > > > > > > >> >> >> >> >> >> >> >> >> >> >> > > > > 238 | + | 238 |
| </ | </ | ||
| - | eSPY is still being developed and as yet doesn' | + | == RPi == |
| + | |||
| + | On the RPi we can reset the internal address pointer of the chip to 0 like this. | ||
| + | < | ||
| + | i2cset -y 1 0x50 0 0 | ||
| + | </ | ||
| + | |||
| + | To read, we first write an address to start at then begin reading, if we keep reading the address | ||
| + | < | ||
| + | i2cset -y 1 0x50 0 0 | ||
| + | i2cget -y 1 0x50 | ||
| + | 0x55 | ||
| + | i2cget -y 1 0x50 | ||
| + | 0xaa | ||
| + | </ | ||
| + | |||
| + | If we want to write to a location we send the address followed by the byte of data. | ||
| + | < | ||
| + | i2cset -y 1 0x50 0 0 0xEE i | ||
| + | i2cset -y 1 0x50 0 0 | ||
| + | i2cget -y 1 0x50 | ||
| + | 0xee | ||
| + | </ | ||
| This overview gives enough information to use the device at a byte level, read the [[# | This overview gives enough information to use the device at a byte level, read the [[# | ||
| Line 281: | Line 298: | ||
| [[http:// | [[http:// | ||
| [[http:// | [[http:// | ||
| + | |||
