Atmel ICE
This device is used to program various Atmel designed processors.
It has one serious fault, in that the sockets are wired back to front but otherwise it works well. The dumb wiring is the main reason for this page. I got it working fine once and now forget how it's broken so need to rediscover the stupidity yet again.
I got the PCBA version of this device in 2019 for £47, they now cost £90 in 2022. Microchip outpace inflation like nobody else.
USB
Bus 001 Device 027: ID 03eb:2141 Atmel Corp. ICE debugger
Ports
The key in the port is on the wrong side so you can either plug the cable in back to front (not recommend) or cut the notch off your cable and turn it around and plug it the right way around at the other end (recommended but I don't accept liability for any error). Maybe Atmel (now MCHP) should just employ competent engineers.
PS. MCHP will sell you mis-wired cables so you do not need to do the above, but having mis-wired cables in your collection may be even worse.
SAM AVR
KEY KEY
TMS TCK TDO TDI SRST GND VTG SRST TRST GND
2 4 6 8 10 2 4 6 8 10
1 3 5 7 9 1 3 5 7 9
VTG GND GND TRST GND TCK TDO TMS NC TDI
Both sockets contain the same signals just wired to
different pins.
SAM = ARM standard and AVR = ATMEL standard.
PIN SAM AVR SWD(1) CORTEX(2)
1 VTG TCK Vref VCC/VREF
2 TMS GND SWIO SWDIO/TMS
3 GND TDO GND GND
4 TCK VTG CLK SWDCLK/TCK
5 GND TMS GND GND
6 TDO SRST SWO SWO/TDO
7 TRST NC KEY KEY
8 TDI TRST NC NC/TDI
9 GND TDI GNDd GND
10 SRST GND RST nRESET
(1) Adafruit SWD adapter
(2) Adafruit Cortex SWD adapter
JTAG ATMEGA2560 ATMEGA32
VTG VCC VCC
GND GND GND
TCK PF4 PC2
TMS PF5 PC3
TDO PF6 PC4
TDI PF7 PC5
JTAG SPI
VTG VCC
GNG GND
TCK SCK
TDO MISO
TDI MOSI
SRST RESET
Test
avrdude -v -B 5 -c atmelice -p ATMEGA32
avrdude: Version 6.3-20171130
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "/etc/avrdude.conf"
User configuration file is "/home/darron/.avrduderc"
User configuration file does not exist or is not a regular file, skipping
Using Port : usb
Using Programmer : atmelice
Setting bit clk period : 5.0
avrdude: Found CMSIS-DAP compliant device, using EDBG protocol
AVR Part : ATmega32
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 4 10 64 0 no 1024 4 0 9000 9000 0xff 0xff
flash 33 6 64 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 2000 2000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 2000 2000 0x00 0x00
lock 0 0 0 0 no 1 0 0 2000 2000 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
calibration 0 0 0 0 no 4 0 0 0 0 0x00 0x00
Programmer Type : JTAGICE3
Description : Atmel-ICE (ARM/AVR) in JTAG mode
ICE hardware version: 0
ICE firmware version: 1.42 (rel. 161)
Serial number : J41800108041
Vtarget : 4.52 V
JTAG clock megaAVR/program: 200 kHz
JTAG clock megaAVR/debug: 1000 kHz
JTAG clock Xmega: 1000 kHz
PDI clock Xmega : 1000 kHz
avrdude: JTAG ID returned: 0x3f 0x20 0x50 0x89
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.08s
avrdude: Device signature = 0x1e9502 (probably m32)
avrdude: safemode: lfuse reads as FF
avrdude: safemode: hfuse reads as 19
avrdude: safemode: lfuse reads as FF
avrdude: safemode: hfuse reads as 19
avrdude: safemode: Fuses OK (E:FF, H:19, L:FF)
avrdude done. Thank you.
