You are here: start » tools » optiboot

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Last revision Both sides next revision
tools:optiboot [2021/09/12 05:45]
darron [Install] 		tools:optiboot [2021/09/19 18:11]
darron [Install]
Line 12: Line 12:
 ./makeall.arduino.sh ./makeall.arduino.sh
 </code> </code>
 +
 +==Get firmware version==
 +
 +<code>
 +git log -n 1 --pretty=format:%H%n
 +0dd4cedfbd6669d47752707486d3625a911bdb12
 +</code>
 +
  
 ==List all firmware== ==List all firmware==
Line 73: Line 81:
 <code> <code>
 avrdude -V -B 5 -c usbasp -p ATMEGA328P -e -u -U lock:w:0x3F:m -U efuse:w:0xFD:m -U hfuse:w:0xDE:m -U lfuse:w:0xFF:m avrdude -V -B 5 -c usbasp -p ATMEGA328P -e -u -U lock:w:0x3F:m -U efuse:w:0xFD:m -U hfuse:w:0xDE:m -U lfuse:w:0xFF:m
-avrdude    -B 5 -c usbasp -p ATMEGA328P -D -u -U flash:v:optiboot_atmega328_pro_8MHz.hex:i +avrdude    -B 5 -c usbasp -p ATMEGA328P -D -u -U flash:w:optiboot_atmega328_pro_8MHz.hex:i 
-avrdude -V -B 5 -c usbasp -p ATMEGA328P -u -U lock:w:0x0F:m+avrdude    -B 5 -c usbasp -p ATMEGA328P -D -u -U lock:w:0x2F:m
 </code> </code>
  
 ==Arduino UNO== ==Arduino UNO==
  
-__Pololu USB AVR Programmer v2.1__+__[[:interfaces:pololu|Pololu USB AVR Programmer v2.1]]__
  
  
 <code> <code>
 avrdude -V -B 5 -P `pavr2cmd --prog-port` -c avrisp2 -p ATMEGA328P -e -u -U lock:w:0x3F:m -U efuse:w:0xFD:m -U hfuse:w:0xDE:m -U lfuse:w:0xFF:m avrdude -V -B 5 -P `pavr2cmd --prog-port` -c avrisp2 -p ATMEGA328P -e -u -U lock:w:0x3F:m -U efuse:w:0xFD:m -U hfuse:w:0xDE:m -U lfuse:w:0xFF:m
-avrdude    -B 5 -P `pavr2cmd --prog-port` -c avrisp2 -p ATMEGA328P -D -u -U flash:w:optiboot_atmega328.hex:i +avrdude    -B 5 -P `pavr2cmd --prog-port` -c avrisp2 -p ATMEGA328P -D -u -U flash:w:optiboot_atmega328.hex:i -U lock:w:0x2F:m
-avrdude -V -B 5 -P `pavr2cmd --prog-port` -c avrisp2 -p ATMEGA328P -u -U lock:w:0x0F:m+
 </code> </code>
  
 +=== Test ===
 +
 +==Arduino Pro Mini with 8 MHz XTAL==
 +
 +<code>
 +$ avrdude -c arduino -b 57600 -D -p m328p -P /dev/ttyUSB0 
 +
 +avrdude: AVR device initialized and ready to accept instructions
 +
 +Reading | ################################################## | 100% 0.00s
 +
 +avrdude: Device signature = 0x1e950f (probably m328p)
 +
 +avrdude: safemode: Fuses OK (E:00, H:00, L:00)
 +
 +avrdude done.  Thank you.
 +</code>
 +
 +===Resources===
 +
 +https://www.engbedded.com/fusecalc/
 +
 +https://www.engbedded.com/conffuse/