You are here: start » boards » mxchip

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
boards:mxchip [2015/01/06 13:49]
darron 		boards:mxchip [2022/11/27 00:29] (current)
darron [Resources]
Line 11: Line 11:
 Whilst this module is relatively inexpensive, the development tools for the MICO O/S cost thousands. This makes the device practically useless for now. Whilst this module is relatively inexpensive, the development tools for the MICO O/S cost thousands. This makes the device practically useless for now.
  
-== Pinout ==+=== Pinout ===
 <code> <code>
      PB0                    PB1      PB0                    PB1
Line 53: Line 53:
 </code> </code>
  
-== Probe ==+=== Probe ===
 <code> <code>
 stm32flash -b 9600 /dev/ttyCP2102 stm32flash -b 9600 /dev/ttyCP2102
Line 71: Line 71:
 </code> </code>
  
-== Modes ==+=== Modes ===
 ^ BOOT PB1 ^  STATUS PB9 ^ Mode of operation | ^ BOOT PB1 ^  STATUS PB9 ^ Mode of operation |
 | 0         |0        | Factory mode    | | 0         |0        | Factory mode    |
Line 77: Line 77:
 | 1         |X        | Working mode| | 1         |X        | Working mode|
  
-== Firmware update mode ==+=== Firmware update mode ===
 The bootloader is entered by holding PB1 low and PB9 high. The bootloader is entered by holding PB1 low and PB9 high.
 <code> <code>
Line 100: Line 100:
 </code> </code>
  
-== Firmware update ==+=== Firmware update ===
 Minicom may be used to send a file using the ymodem protocol. Minicom may be used to send a file using the ymodem protocol.
  
Line 130: Line 130:
 </code> </code>
  
-== Flash memory map ==+=== Flash memory map ===
 ^Address   ^Function | ^Address   ^Function |
 |0x8000000 |Boot loader| |0x8000000 |Boot loader|
Line 138: Line 138:
 |0x80C0000 |RF driver| |0x80C0000 |RF driver|
  
-== Standalone demo ==+=== Standalone demo ===
  
-Install [[:tools:libopencm3|OpenCM3]] and build examples.+Install [[:tools:libopencm3|OpenCM3]].
  
-Enter ST ISP mode using BOOT0, RX and TX as show in the pinout above.+Install [[:tools:stm32flash|STM32Flash]]. 
 + 
 +Enter ST ISP mode using BOOT0, RX and TX as shown in the pinout above.
  
 Fetch the demo and edit the Makefile, change the serial device to your host device (TTYISP). Fetch the demo and edit the Makefile, change the serial device to your host device (TTYISP).
Line 157: Line 159:
 </code> </code>
  
-You can restore the MICO O/S from the emw3162.bin file, do not overwrite it.+You can restore the MICO O/S from the emw3162.bin file, do not overwrite it.\\
 Eg. Eg.
 <code> <code>
 stm32flash -w emw3162.bin -b 115200 /dev/ttyAMA0 stm32flash -w emw3162.bin -b 115200 /dev/ttyAMA0
 </code> </code>
 +
 +===Resources===
 +
 +[[https://www.st.com/resource/en/datasheet/stm32f205rg.pdf|MCU datasheet]]
 +
 +[[https://www.st.com/resource/en/reference_manual/cd00225773-stm32f205xx-stm32f207xx-stm32f215xx-and-stm32f217xx-advanced-arm-based-32-bit-mcus-stmicroelectronics.pdf|MCU reference manual]]