You are here: start » boards » msp430

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
boards:msp430 [2020/10/10 14:37]
darron [MSP430 Launchpad] 		boards:msp430 [2020/12/27 00:46]
darron
Line 1: Line 1:
-==== MSP430 Launchpad ====+==== MSP-EXP430G2 Launchpad ====
 <wrap right> <wrap right>
 {{:boards:msp430.jpg?200}} {{:boards:msp430.jpg?200}}
 </wrap> </wrap>
  
-The MSP430 Launchpad from TI is an inexpensive development board that comes with two processors, a 32K crystal, two headers sockets, a usb lead and two stickers.+The MSP-EXP430G2 Launchpad from TI is an inexpensive development board that comes with two processors, a 32K crystal, two headers sockets, a usb lead and two stickers.
  
-The latest boards come with the MSP430G2553 and the MSP430G2452 processors but the first revision came with the MSP430G2211 and MSP430G2231.+The latest boards come with the MSP430G2553 and the MSP430G2452 processors but the first revision came with the MSP430G2231 and MSP430G2211.
 === Linux === === Linux ===
  
Line 19: Line 19:
 USB USB
  
-VCC                     GND  +VCC         3V3                                GND  
-P1.0 (LED1)             XIN +P1.0 (LED1) A0                 P2.6            XIN 
-P1.1 (UART)            XOUT +P1.1 (UART) A1 TXD             P2.7           XOUT 
-P1.2 (UART)            TEST +P1.2 (UART) A2 RXD                            TEST 
-P1.3 (S2)          (S1) RST +P1.3 (S2)   A3                           (S1)  RST 
-P1.4                   P1.7 +P1.4        A4             SDA MISO A7        P1.7 
-P1.5            (LED2) P1.6 +P1.5        A5 SCK         SCL MOSI A6 (LED2) P1.6 
-P2.0                   P2.5 +P2.0           CS                             P2.5 
-P2.1                   P2.4 +P2.1                                          P2.4 
-P2.2                   P2.3+P2.2                                          P2.3
  
-P1.3  P1.0     RESET    GND +                                               GND 
-S2    P1.6     S1       GND+P1.3   P1.0 P1.6                   RESET       GND 
 +S2     LED1 LED2                   S1          VCC 
 +       RED  GREEN
 </code> </code>
  
-=== LED demo ===+=== Launchpad demo ===
  
-First install the required development tools.+First install the [[tools:msp430gcc|development]] and [[tools:mspdebug|programming]] tools. 
 + 
 +Demo
  
 <code> <code>
-apt-get install binutils-msp430 gcc-msp430 msp430-libc mspdebug msp430mcu+hg clone http://hg.kewl.org/pub/msp430-launchpad/ 
 +cd msp430-launchpad 
 +make 
 +make program
 </code> </code>
  
-TODO+The board will flash the LEDs until the button is pressed to 
 +enter probe mode.
  
 +Probe mode sends the binary encoded value of the chip
 +temperature over the communications port.
 +
 +Communication can be tested with picocom
 <code> <code>
-mspdebug rf2500 +picocom -b 2400 /dev/ttyACM0 
-MSPDebug version 0.22 - debugging tool for MSP430 MCUs +</code>
-Copyright (C) 2009-2013 Daniel Beer <dlbeer@gmail.com> +
-This is free software; see the source for copying conditions.  There is NO +
-warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.+
  
-Trying to open interface 1 on 036 +Or, 
-Initializing FET... +<code> 
-FET protocol version is 30394216 +linux-serial-test -s -R -t -p /dev/ttyACM0 
-Set Vcc: 3000 mV +</code>
-Configured for Spy-Bi-Wire +
-Device ID: 0x2553 +
-  Code start address: 0xc000 +
-  Code size         : 16384 byte = 16 kb +
-  RAM  start address: 0x200 +
-  RAM  end   address: 0x3ff +
-  RAM  size         : 512 byte = 0 kb +
-Device: MSP430G2553/G2403 +
-Number of breakpoints: 2 +
-fet: FET returned NAK +
-warning: device does not support power profiling +
-Chip ID data: 25 53+
  
-Available commands: +It should be noticed that the TI demo was written for devices without a hardware UART. 
-    =           erase       isearch     power       save_raw    simio        +=== Resources ===
-    alias       exit        load        prog        set         step         +
-    break       fill        load_raw    read        setbreak    sym          +
-    cgraph      gdb         md          regs        setwatch    verify       +
-    delbreak    help        mw          reset       setwatch_r  verify_raw   +
-    dis         hexout      opt         run         setwatch_w  +
  
-Available options: +[[http://www.ti.com/ww/en/launchpad/launchpads-msp430-msp-exp430g2.html|Product page]]
-    color                       gdb_loop                     +
-    enable_bsl_access           gdbc_xfer_size               +
-    enable_locked_flash_access  iradix                       +
-    fet_block_size              quiet                        +
-    gdb_default_port            +
  
-Type "help <topic>" for more information. +[[https://www.ti.com/product/MSP430G2452|MSP430G2452 product page]]
-Use the "opt" command ("help opt") to set options. +
-Press Ctrl+D to quit.+
  
-(mspdebug) +[[https://www.ti.com/product/MSP430G2553|MSP430G2553 product page]]
-</code>+
  
-=== Resources ===+[[https://www.argenox.com/library/msp430/|Tutorial]]
  
-[[http://www.ti.com/ww/en/launchpad/launchpads-msp430-msp-exp430g2.html|Product page]]+[[https://github.com/msp430club|Examples]]