You are here: start » interfaces » cp2102

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
interfaces:cp2102 [2015/01/06 20:37]
darron 		interfaces:cp2102 [2020/08/22 06:07] (current)
darron [Linux]
Line 4: Line 4:
 </wrap> </wrap>
  
-This is a high speed USB UART which should easily attain 460800 baud in Linux or even higher.+This is a high speed USB UART and a genuine item should easily attain 460800 baud in Linux or even higher. 
 + 
 +=== BAITE module (pictured) ===
  
-=== BAITE Cp2102 module (pictured) === 
 Transmit is labelled RXD and receive as TXD on this module. Transmit is labelled RXD and receive as TXD on this module.
 +
 +=== CJMCU module ===
 +
 +This module uses a cp2102 device incorrectly wired with
 +4v4 on their output pins instead of 3v3. This module is totally
 +unreliable at 460800 baud.
 +
 +A source on the web explains that the RESET pin is incorrectly
 +pulled high to VUSB.
 +
 +=== 6 in 1 USB to TTL RS232 USB TTL to RS485 ===
 +
 +There is lot going on here and none has been tested. A diagram exists
 +explaining the switches.
 +
 +{{:interfaces:6in1.jpg?400}}
 +
 +<code>
 +Mode Pin Function
 +TTL Level Interface TXD TTL Transmit
 +TTL Level Interface RXD TTL Receive
 +TTL Level Interface GND TTL ground
 +232 Level Interface 232-TX 232 Transmit
 +232 Level Interface 232-RX 232 Receive
 +232 Level Interface GND 232 Ground
 +485 Level Interface A 485A+
 +485 Level Interface B 485B-
 ++5V Voltage Output +5V +5V Voltage Output
 +3.3 Voltage Output 3V3 3.3V Voltage Output
 +DTR Output DTR Special Function
 +RTS Output RTS Special Function
 +</code>
  
 === Linux === === Linux ===
  
 == udev /dev/ttyCP2102 == == udev /dev/ttyCP2102 ==
 +
 <code> <code>
-KERNEL=="ttyUSB*",ATTRS{idVendor}=="10c4",ATTRS{idProduct}=="ea60",ATTRS{serial}=="0001",\ +KERNEL=="ttyUSB*",\ 
-    GROUP="dialout",MODE="0660",RUN+="/bin/ln -sf %k /dev/ttyCP2102"+    ATTRS{idVendor}=="10c4",\ 
 +    ATTRS{idProduct}=="ea60",\ 
 +    ATTRS{serial}=="0001",\ 
 +    GROUP="dialout",\ 
 +    MODE="0660",\ 
 +    RUN+="/bin/ln -sf %k /dev/ttyCP2102"
 </code> </code>
  
 == udev by-id == == udev by-id ==
 +
 <code> <code>
 /dev/serial/by-id/usb-Silicon_Labs_CP2102_USB_to_UART_Bridge_Controller_0001-if00-port0 /dev/serial/by-id/usb-Silicon_Labs_CP2102_USB_to_UART_Bridge_Controller_0001-if00-port0
 </code> </code>
-udev by-id is not supported by the k8048 Microchip PIC programmer. 
  
-=== k8048 Microchip PIC programmer ===+ 
 +=== Pickle Microchip PIC ICSP ===
  
 == Low Voltage Programming with VPP at 3V3 == == Low Voltage Programming with VPP at 3V3 ==
Line 48: Line 88:
 == Configuration == == Configuration ==
 <code> <code>
-DEVICE=/dev/ttyUSB0+DEVICE=TTY 
 +IFACE=/dev/ttyUSB0
 SLEEP=0 SLEEP=0
 BITRULES=0x001F BITRULES=0x001F