====Raspberry Pi PICO====
<wrap right>
{{:boards:pipico.jpg?100}}
\\ \\
{{:boards:four_picos.jpg?100}}
</wrap>

Dual core Arm Cortex M0 microcontroller designed to run MicroPython.

There are four varieties of this board produced by RPi. The differences
are whether they come pre-installed with header pins and a debug socket
and if they have a WiFi adapter on board.

===Tools===

Read this [[https://datasheets.raspberrypi.com/pico/getting-started-with-pico.pdf|guide]]. Within
is the setup procedure for development tools is as follows:

<code>
wget https://raw.githubusercontent.com/raspberrypi/pico-setup/master/pico_setup.sh
sh pico_setup.sh
</code>

This will install the ARM compiler, OpenOCD, the SDK, examples, and various other things.

OpenOCD is built from source with the following options:
<code>
./configure --enable-ftdi --enable-sysfsgpio --enable-bcm2835gpio --enable-picoprobe
</code>
===J-Link===

<wrap right>
{{:boards:pico-segger.jpg?200}}
</wrap>

Segger J-Link can be use to interact with the PICO via the debug port.

==CORE 0==

<code>
echo "exit" | /opt/JLink/JLinkExe -device RP2040_M0_0 -if swd -speed 4000 -autoconnect 1 -nogui 1
SEGGER J-Link Commander V7.82a (Compiled Oct 31 2022 11:25:49)
DLL version V7.82a, compiled Oct 31 2022 11:25:22

Connecting to J-Link via USB...O.K.
Firmware: J-Link EDU Mini V1 compiled Oct 21 2022 11:17:52
Hardware version: V1.00
J-Link uptime (since boot): 0d 00h 09m 41s
S/N: 801011752
License(s): FlashBP, GDB
USB speed mode: Full speed (12 MBit/s)
VTref=3.259V
Device "RP2040_M0_0" selected.


Connecting to target via SWD
ConfigTargetSettings() start
J-Link script: ConfigTargetSettings()
ConfigTargetSettings() end
Found SW-DP with ID 0x0BC12477
DPIDR: 0x0BC12477
CoreSight SoC-400 or earlier
Scanning AP map to find all available APs
AP[1]: Stopped AP scan as end of AP map has been reached
AP[0]: AHB-AP (IDR: 0x04770031)
Iterating through AP map to find AHB-AP to use
AP[0]: Core found
AP[0]: AHB-AP ROM base: 0xE00FF000
CPUID register: 0x410CC601. Implementer code: 0x41 (ARM)
Found Cortex-M0 r0p1, Little endian.
FPUnit: 4 code (BP) slots and 0 literal slots
CoreSight components:
ROMTbl[0] @ E00FF000
[0][0]: E000E000 CID B105E00D PID 000BB008 SCS
[0][1]: E0001000 CID B105E00D PID 000BB00A DWT
[0][2]: E0002000 CID B105E00D PID 000BB00B FPB
Cortex-M0 identified.
</code>

==CORE 1==

<code>
echo "exit" | /opt/JLink/JLinkExe -device RP2040_M0_1 -if swd -speed 4000 -autoconnect 1 -nogui 1
SEGGER J-Link Commander V7.82a (Compiled Oct 31 2022 11:25:49)
DLL version V7.82a, compiled Oct 31 2022 11:25:22

Connecting to J-Link via USB...O.K.
Firmware: J-Link EDU Mini V1 compiled Oct 21 2022 11:17:52
Hardware version: V1.00
J-Link uptime (since boot): 0d 00h 09m 48s
S/N: 801011752
License(s): FlashBP, GDB
USB speed mode: Full speed (12 MBit/s)
VTref=3.260V
Device "RP2040_M0_1" selected.


Connecting to target via SWD
ConfigTargetSettings() start
J-Link script: ConfigTargetSettings()
ConfigTargetSettings() end
Found SW-DP with ID 0x0BC12477
DPIDR: 0x0BC12477
CoreSight SoC-400 or earlier
Scanning AP map to find all available APs
AP[1]: Stopped AP scan as end of AP map has been reached
AP[0]: AHB-AP (IDR: 0x04770031)
Iterating through AP map to find AHB-AP to use
AP[0]: Core found
AP[0]: AHB-AP ROM base: 0xE00FF000
CPUID register: 0x410CC601. Implementer code: 0x41 (ARM)
Found Cortex-M0 r0p1, Little endian.
FPUnit: 4 code (BP) slots and 0 literal slots
CoreSight components:
ROMTbl[0] @ E00FF000
[0][0]: E000E000 CID B105E00D PID 000BB008 SCS
[0][1]: E0001000 CID B105E00D PID 000BB00A DWT
[0][2]: E0002000 CID B105E00D PID 000BB00B FPB
Cortex-M0 identified.
</code>

===Resources===

https://github.com/raspberrypi/pico-sdk

https://github.com/raspberrypi/pico-examples

https://wiki.segger.com/Raspberry_Pi_Pico