==== Espressif Systems ESP8266====
<wrap right>
{{:boards:esp8266-ch340.jpg?200}}
</wrap>

The Espressif Systems ESP8266 is used in cheap WiFi modules. It embeds an Xtensa LX3 CPU. ESP8266 boards named ESP-XX come with at least 1/2 megabyte of SPI flash for program storage.

Also see [[tools:tasmota|tasmota]] for various applications of this processor.
=== Pinout ===

__ESP-01__

<code>
U0TXD    2 1 GND
CHIP_EN  4 3 GPIO2
EXT_RSTB 6 5 GPIO0
VDD      8 7 U0RXD

Component side with antenna to right
</code>

=== Power ===

A well regulated power supply is suggested. An LD1117 3V3 has been tested and works well.

<code>
3V3 ---------- VDD
3V3 ---10K---- CHIP_EN
GND ---------- GND
</code>

=== AT firmware update ===

<wrap right>
{{:boards:esp01-3.jpg?200}}
</wrap>

The default AT firmware can be updated using [[:tools:esptool|ESPTool]].

To program the chip, keep GPIO0 low and reset the device on EXT_RSTB.

<code>
wget "https://wiki.kewl.org/downloads/v0.9.2.2 AT Firmware.bin"
esptool.py --port /dev/ttyUSB0 write_flash 0x000000 "v0.9.2.2 AT Firmware.bin"
Connecting...
Erasing flash...
Writing at 0x0007ef00... (100 %)

Leaving...
</code>

=== AT console ===
The updated AT firmware uses 9600 baud by default, the original is 115200.

<code>
3V3 UART       ESP-XX
========       ======
RX  -- 470R -- U0TXD
TX  -- 470R -- U0RXD
GND ---------- GND
</code>
<code>
picocom -b 9600 --omap crcrlf /dev/ttyUSB0
AT+RST
...
[System Ready, Vendor:www.ai-thinker.com]
AT+GMR
0018000902
OK
AT+CWMODE=1
OK
AT+CWLAP
+CWLAP ...
</code>

The commands above reset the device, set its mode of operation and scan for access points.

=== NodeMcu ===
<wrap right>
{{:boards:nodemcu.jpg?200}}
</wrap>
NodeMcu is a LUA interpreter than runs on the ESP-XX chip. It can be used to
communicate over the network and control the GPIOs.

We will use [[:tools:esptool|ESPTool]] to install NodeMcu for esp8266.

<code>
git clone https://github.com/nodemcu/nodemcu-firmware
git reset --hard fb967dd8a2c8282e146626642bf24e8c90cdbcd0
cd nodemcu-firmware/pre_build/0.9.5
esptool.py --port /dev/ttyUSB0 write_flash 0x000000 nodemcu_20150127.bin
esptool.py v2.0-beta2
Connecting....
Detecting chip type... ESP8266
Uploading stub...
Running stub...
Stub running...
Attaching SPI flash...
Configuring flash size...
Auto-detected Flash size: 512KB
Flash params set to 0x0000
Compressed 395836 bytes to 267867...
Wrote 395836 bytes (267867 compressed) at 0x00000000 in 23.5 seconds (effective 134.7 kbit/s)...
Hash of data verified.

Leaving...
Hard resetting...
</code>

Build 20150212 firmware can be found in pre_build/latest/nodemcu_latest.bin
=== NodeMcu console ===
A regular console at 9600 baud is used to communicate with NodeMcu. The same connection scheme as per the AT console (above) is used.
<code>
picocom -b 9600 /dev/ttyUSB0
NodeMCU 0.9.5 build 20150127  powered by Lua 5.1.4
lua: cannot open init.lua
> gpio.mode(3, gpio.OUTPUT)
> gpio.write(3, gpio.HIGH)
> gpio.write(3, gpio.LOW)
</code>

In the above we set GPIO0 to an output, set it high, then set it low.

=== NodeMcu pins ===
<wrap right>
{{:boards:esp01.jpg?200}}
</wrap>

^pin ^GPIO ^ ESP-01 |
|0   |16|    |
|1   |5|     |
|2   |4|     |
|3   |0|     5|
|4   |2|     3|
|5   |14| |
|6   |12| |
|7   |13| |
|8   |15| |
|9   |3| |
|10  |1| |
|11  |9| |
|12  |10| |

Although the ESP-01 only has 2 GPIOs, NodeMcu has I2C support and a circuit such as [[:projects:esp|this]] can extend its capabilities.

=== Resources ===

[[http://www.nodemcu.com/index_en.html|NodeMcu home page]]